Replacement for EveryDrop Refrigerator Water Filter

Three to five gallons.
Most manufacturers' recommend that you run between three to five gallons of water through your refrigerator water filter before consumption. For refrigerators that don't dispense water, discard the first two batches of ice.

If your EveryDrop refrigerator water dispenser doesn’t work, the primary reasons usually are freezing of the water tank and water filter issues.
When the supply tube is frozen, which causes a breakdown of a fridge’s water dispenser, it’ll be tough to verify. Look at all connections precisely at the bottom or top of your refrigerator’s door. Try to dismantle the hose and blow warm air through the tube to remove clogs from the dispenser.

Waterdrop filters are typically effective at removing chlorine, radon, man-made chemicals, volatile organic chemicals and benzene. However, no filter is perfect, so they cannot remove all possible water contaminants. Most refrigerator filters offer little protection against the following: Arsenic.

Waterdrop replacements for the EveryDrop fridge water filter, NSF Certified to reduce harmful substances such as chlorine, lead, cyst, benzene, etc. Replacement for EveryDrop filter 1, filter 2,filter 3,filter 4,filter 5,EDR1RXD1,EDR2RXD1, EDR3RXD1, EDR4RXD1, EDR5RXD1 and more. There is no worry about possible water leakage, as our cartridge perfectly fits the original. We are known for being a professional and trustworthy filter manufacturer, and we sell water filters directly from the factory.

Yes. In the fine print, you see it is NSF 42 for water treatment standard. Filters for making flouride-free water are NSF 53

Waterdrop filters are tested and certified by NSF International against
NSF 401 for the reduction of incidental contaminants, including Phenytoin, Ibuprofen, Naproxen, Estrone, BPA and Nonyl phenol; NSF 53 for the reduction of health-related contaminants, including Lead, Benzene; NSF 42 for the reduction of Chlorine, Taste and Odor

To flush a new filter, run a gallon or two from the water dispenser, collecting the water in a pitcher. Discard the water or use it to water your plants. If you only have an ice maker in the refrigerator, you may have to throw away the first few batches of ice if they are discolored.

NSF 401 certified water filters are the best water filter for EveryDrop refrigerator.

Waterdrop Refrigerator Water Filters replacement for EveryDrop filter 1, filter 2,filter 3,filter 4,filter 5,EDR1RXD1,EDR2RXD1, EDR3RXD1, EDR4RXD1, EDR5RXD1 and more. Please check the product page for more details. The manufacturer's names and part numbers have been used for reference purposes only.

Recommended to replace your filter every 6 months or 200 gallons for optimum performance, whichever comes first will vary based on water quality.

1) Locate your water filter cover in the upper right corner inside your refrigerator or in the base grille.
2) Lift the filter door up.
3) Pull the filter out and discard it.
4) Open your new filter and remove the protective coverings from the O-rings. NOTE: Be sure the O-rings are still in place after the cover has been removed.
5) When inserting the new filter into the filter slot, make sure the arrow is pointing upward.
NOTE: Do not force the water filter in. If it does not slide in easily, rotate it to ensure the notches are properly aligned with the grooves.
6) Push the filter door closed so that it snaps into place.
7) Once your filter is replaced, run four gallons of water through the line to properly flush the new filter

1) Locate your water filter cover in the upper righthand corner inside your refrigerator or in the base grille.
2) Pull open the filter door.
3) Pull the filter so it is angled down, turn it to the left and pull. Discard the old filter.
4) Open your new filter and remove the protective coverings from the O-rings.
NOTE: Be sure the O-rings are still in place after the cover has been removed.
5) When inserting the new filter into the filter slot, make sure the arrow is pointing upward.
NOTE: As you push in, the filter will begin to rotate. Turn to the right until it locks into place.
6) Push the filter door up so that it snaps closed.
7)Once your filter is replaced, run four gallons of water through the line to properly flush the new filter.

1) Locate your water filter cover in the lower left corner of the refrigerator base grille.
2) Push down on the eject button and the filter will be released. Pull the filter out.
3) Remove the filter cap by turning it counterclockwise. Pull off.
4) Open your new filter and remove the protective coverings from the O-rings.
NOTE: Be sure the O-rings are still in place after the cover has been removed.
5) Place the filter cap on the new cartridge, making sure the ridges align. Turn the cap clockwise to lock into place.
6) When inserting the new filter into the filter slot, make sure the arrow is pointing to the left, then gently push in.
7) Push the filter in until the eject button pops back out.
8)Once your filter is replaced, run four gallons of water through the line to properly flush the new filter.

1) Locate your water filter cover in the upper right of your refrigerator interior.
2) If the filter tab in your refrigerator is facing outwards, push on it and pull the cover down.
If the tab is on the bottom of the cover, pull forward on the small lever on the cover and pull down to open.
3) Turn the filter to the left and pull. Discard the old filter.
NOTE: If this is a first time installation, a cap will be inside the filter opening. Turn it counterclockwise and pull out.
4) When inserting the new filter, line it up with the grooves, push in and turn to the right.
5) Push up on the filter to lock in place.
6) Push the filter door up so that it snaps closed.
7) Once your filter is replaced, run four gallons of water through the line to properly flush the new filter.

1)Locate your water filter cartridge cap in the front of the refrigerator base grille.
2) Rotate the cap counterclockwise until the handle is in a vertical position, then pull straight out.
3) Remove the filter cap by sliding it off the end of the filter. Keep the cap, but discard the old filter.
4) Open your new filter and remove the protective coverings from the O-rings.
5) Slide the cartridge cap onto the end of the new filter.
6) When inserting the new filter into the filter slot, make sure cap handle is in a vertical position. Push all the way in.
7) Rotate the filter cap clockwise to a horizontal position.
8) Once your filter is replaced, run four gallons of water through the line to properly flush the new filter.